hoola

The issue with the jeopardy button and overall proximity sensitivity has been resolved. The pulse from the last piezo and it's delivery to the reset pin must necessarily go thru the button, which the inductance and self capacity of the cabling affects the waveform drastically as it is moved or held. A relay needs to be installed to isolate the system from the button. I have temporarily removed the button from the circuit and simply push the needed connection together with an insulated probe and get the desired weight gain without the previously mentioned artifacts and the stability of the readings are further increased. Tests after this change are showing weight gains of 2-3mg with as little as 250v supply. Increasing the supply back up to 500v has provided up to 10mg of weight gain when activated, but that is an outlier with the desired waveform still rather unstable over long periods as the stack warms up, and not easily reproducible, so that represents an exaggerated reading that may be readily attainable with further improvements. Oddly, the nfb circuits have little effect upon the new pulsed waveform and turning them up, down or off seems to has no apparent effect on readings and very little effect upon scope waveforms, so the nfb circuts may not be needed in a final product. I am finding that turning off piezos 2 and 4, and just running 1,3,5 seems to deliver the cleanest trace and highest weight gains, at least as the machine is hooked up at present. Still around 44khz but am finding good results up to 52khz clock freq. The spec sheet shows the piezos to have an individual resonance of 25khz, so finding good results in the range of twice that seems logical.

Further tests have shown similar weight gains occur with supply voltages in the 375-400v range, no changes noted with 300v and below.

The reset based circuit has created a pulsed scan schedule as hoped, and I am getting 2-3mg weight gain on the scale when activated with the jeopardy button, and when released, the weight quickly dissapears back down to the starting indication. Testing over a period of 2 hours has has shown a reliable force seems to be developed. The jeopardy button is no longer controlling the nfb systems, which have been put permenantly on, it now contols activating the reset pulse contol system. I have to use the 800v supply to get these readings, and have had to replace the output transistor load resistors as they were getting too hot with this new arrangement and have replaced them with slighlly higher resistances and doubled the wattage. They still run hot, as well as the output transistors themselves, so tests are limited to 20 mins or so with a 20 min break for things to cool off as the unit is in a closed off area to prevent air current disturbances. A strange feature has developed along with this change in that touching or even getting near the chassis, jeopardy cord or button causes wild swings in the scope traces and just getting anything near the stack casuses max reaction of the odd behaviour. Placing the microwave leak detector near (2") from the stack causes this behavior to manifest most . The "click" sound is now a steady hash of clicks, and perhsps future tests will confim my initial findings

Upon upgrading the scale assy, I have found that the lever arm was oscillating at a very low frequency, in the order of seconds, and that my observed thrust readings were due to riding that resonace up and getting appartent thrust, then getting reverse readings, followed by no readings. This explains the two months of false readings that occured in my normal testings. However, the rare anomolus "click" upon shutting down the nfb system, say one out of a thousand tries, which always read 2-3mg weight gain, is the only potential lead I have to proceed with. This only happened a few times, and while no possibility seems for continuous thrust, perhaps a pulsed on/off control can be added that can allow the system to build up thrust over a period of ten or so cycles, then at the right time of shutting off the scan at the appropriate piezo, the "tick" sound can be recreated and see if it coorelates to a release of stored energy that will give the weight increase observed previously. There is a "reset" control on pin 15, currently unused, that will halt the count, then restart at output 1 again (labeled as output 0). I will draw up a circuit to interrupt the scans at regular, controlled intervals, and make the scan end point selectible on which piezo is the last scanned. I have observed that the scan pulses are sometimes higher when some of the piezos are turned off, depending on drive frequency, and PWM settings, so it seems possible that the max stored thrust may be available before the last piezo it driven. I have shifted over to approx 44khz as clock frequency from the previous 188khz. If anyone golfs, the click sound I am refering to is the sound of a perfectly hit long shot on the driving range which doesn't need to be hit very hard to get great range.

I have found the "chase" function to help with stabilizing certain waveforms, but still figuring out the pattern, mostly turn off that function until a useable waveform established, then switch them on separately and see which one or combinations help or detract. I got the microwave leak detector and have found no emissions, but having the suppressors across each element, no way to tell without removing them to see if microwaves ever did develop, which I may do at some point when I tear down the stack and inspect it. I have been having other issues with any supply going much over 300 volts in that I am achieving a much higher pulse or sets of pulses, but the noise is also much harder to control, and probably swamps any thrust signal should it show up and the waveform collapses too quickly to try a scale balance test. I have gone back to 300 volts as I am getting a weight gain of 2 to 3 milligrams reading on the scale upon activation with reasonably stable waveforms at that voltage. I have a "jeopardy" button attached to the wall, then swung into the chassis for physical isolation. This button turns the NFB circuits on and off. When off, the lack of NFB should allow the pulse echos to nuetralize and eliminate any possible directional thrust. I have noted that on occasion there is a "tick" when I turn off the NFB accompanied by an additional increase in observed weight above the 2-3 mg level by another 2-3 mgs.. I think this is due to the pulse pattern just completed upon shutoff, hence no additional noise from the next scan period, thereby extra thrust. This could be how the Woodward team is getting thrust, as they say it largely occurs upon the end of the stimulation periods. (They report having blown up stacks with running them to the point of fracture.) The stack is mounted on the short end of the level and is pulsing order down, so the observed thrust is in the correct direction as the stack should be getting lighter, allowing the long end contacting the scale to register the increase. I have found that the wires from the chassis to the stack are a main source of unstable readings, plus the pivot point on the level arm seems an issue also. Upon setting up the scale, up to several minutes of readings bouncing around of plus or minus 5 millilgrams are noted. I have found that placing a speaker on the underside of the bench directly below the scale/lever assy helps reduce this issue. The speaker is driven by an FM radio on an empty channel, giving white noise. This seems to vibrate the entire assembly out of a tendency to stick to any particular spot, and now the instabilities are lowered to plus or minus two milligrams, and settle down to a stasis point more quickly. The next step is to mount the stack upside down, which should make the stack heavier, giving a scale indication of a a lower value.

I am thinking about enhancing the NFB circuits by using the unused 7014 output ports to "chase after" each piezo as they are serially stimulated. At this point, the five NFB circuits are all turned on at once, at the end of the fifth piezo stimulation, during retrace. If I were to add on 4 ancillary NFB trunk lines, one for each NFB circuits of the first four piezos, to be activated individually just after each of these first four piezos gets stimulated, the NFB circuits would "chase after" each pulse, quieting it's aftermath on the fly. When the fifth piezo is done stimulation and the normal collective triggering of all of the NFB circuit occurs during retrace , there should be much less noise in the system in general for it to have to deal with, most of it having be negated during the course of the sweep, not waiting till after the last of the scans occur with all the chaotic echoing that has accumulated in the stack. This could lower the counter thrust, raising efficiency and reducing noise, which could help stabilize the magic waveform after I go back to high voltage tests. I am still waiting on a microwave detector, that's on order and have begun accumulating microwave doors from salvage to take out the screens to overlay the confinment box in a sort of Faraday cage. I have also added a 36pf cap in series with a 27K resistor across each piezo directly at the connections, and placed two ferrite beads on each input lead for added suppression. The RC combo acting as a low pass filter, absorbing frequencies much above 200khz. Current low power tests altered to accomodate this new arrangement are going well, as the overall frequency and duty cycles are only slightly affected. Still running at 188khz.

does anyone know if piezos are capable of direct microwave transmission? I can't find anything online regarding this, but I was hoping for some comfirmation of that, which would explain what happened in the first high output test with the melted chocolate last Monday. I knew early on that some RF came out of the area near the stack, having occasionally placed an AM radio near and picking up hashy noise peaking at about the mid dial area (1mhz) and trailing off at the high end. I didn't think any more about it till now, as the distance was short, having to set the radio within a few inches and just guessing the stack was the source, didn't seem important at the time if it was the stack or something else, harmonics from the audio generator, perhaps, but very unlikely. At this point I was driving the stack at only 25khz, barely above audio. Perhaps the microwaves, if they indeed exist, came from the lead wires to the stack, and only generated within the stack, but having no way to get out physically, till they hit the input lead wires, which turn also into transmission antennas. I guess the thing to do now is to go back to low power experiments specifically to try to determine the source of any RF that is generated. Reducing the supply back down to 200V should limit the radiant energy to a few milliwatts of whatever is coming out of it. Hopefully, shielding the input wires to chassis ground will solve the issue, and be a quick, easy fix.

If anyone has had experience in dealing with microwave suppression in a system similar to mine, please advise of what sources you had for both suppression and reflection materials and tips on how to apply them. It would be funny if what the Shawyer engine uses for thrust, proves to be one of the Woodward engine's waste products.

Today I got in five new nte 165 horizontal output transistors and installed them and operated the machine at a 700V driver supply voltage for the first time. I had the machine in it's normal position on the bench inside the air current isolation box and transparent cover over the top. After about ten minutes of attempting to get a familiar waveform on the scope, shutting the unit on and off to make adjustments in drive frequency and pulse duration, I powered down as the new transistors were running warmer than I had anticipated. Taking what I was anticipating as a short break, I opened up the chocolate container that was sitting on a shelf about 2 feet from the stack, and noticed that the chocolate had melted, and more so on one side that the other, the side toward the unit was nearly liquified. The serendipedous discovery of the microwave oven was a chocolate bar melted in the tech's pocket, and indeed I could be replicating that here. The temperature here is mild, outside is mid 70s, and the house is opened up and at the same temperature, and nothing hot was placed near the container. So I have discovered a major issue to address, and fortunately quickly enough to avert overexposure to the microwaves. I certainly did not imagine this to be an issue, but it may prove to be. Further tests will be needed to be positive of the cause of the melted chocolate. I need to get a microwave detector and appropriate shielding laminated onto the isolation box before any further testing can be safely done.

I built a simple passive twin tee notch filter for the 188khz pilot signal and placed it in the nfb loops one at a time and observed a minor additional suppression of noise, and very little suppression of forward pulse ( as the trap is active during drive sequence). Under higher voltage tests these additional noise suppression traps may be helpful in maintaining waveform stability, but it would leave me stuck at the 188mhz freq unless they are also changed in tandem.

upon retesting the piezo simply held up to the stack with no connections, I still see no trace difference but the sound that the stack makes does change a little. One of the diagnostic tools is to monitor the noise, a medium level chirpy hash mixed with various whistles and clicks, sometimes a rather pleasant sound like a sleep machine.

have found that dressing the lead wires into loosely wrapped pairs of P1-P2 and then P3-P4, and keeping P5 and ground separate has contributed to a higher peak output and more consistent and "resilient" waveform. Before this change even careful handling of the stack would greatly perturb the image. Now the contact issue seems to be gone too. That was always a sensitive spot on each element and now I can poke them with a nylon probe and see no disturbances. I suspect that arranging the leads in this manner has simplified the "conversation" going on between the elements (less noise). Also, have seen that just holding a piezo disc edge to edge with any of the five active elements has a further calming effect. There were no electrical connections, so I added them back on and tried shorting them out and saw no difference. Reversing the polarity of the element (simply flipping it over) also seems to make no difference. Have tried other items, such as metal screwdriver blades, and other metallic and non metallic objects which have no effect. It seems as if the piezos are "talking" to each other, edge to edge even under casual pressure. I have two ways of monitoring the stack now, the edge connector and monitoring the voltage expressed to the #3 piezo through a 10 megohm resistor. In the voltage monitoring, the voltage gain and the strong negative feedback pulse sequence are clearly evident.

As I have finally got a stable enough trace to begin to fine tune things, it seems that the interelectrode capacity between the stack lead wires and the contacts themselves are influencing stack behavior. A perfect waveform is being achieved with spacing of certain wires and interleaving of others just before they attach to the contacts. The contacts themselves are round to match the ring size with the necessary bump out for solder terminals. These contact pads appear to offer some additional effects of concern, as they form small variable capacitors, being directly attached to the piezos. I had attributed certain odd behaviors to the contact material (phosphor bronze) and was going to make the next stack with heavy aluminum foil, but now I think that wouldn't help with the conductivity issue, but might make the variable cap. issue worse, with them vibrating more randomly than the rather inflexible bronze. A possible minimizing of the issue might be to stagger the contacts in a spiral around the perimeter, keeping capacitive interactions to a minimum. This seems to answer the question of why a 36pf capacitor has a strong effect at the relatively low frequency of 188khz.

The signal that I am now tracing seems as likely to offer potential thrust as any observed so far at a new 188khz frequency. The five scan pulses have been merged into a single parabolic waveform that pops up smoothly from baseline, increases linearly in amplitude until an upward spike at the end, signifying a possible amplification of the pulses as they progress down the stack. After the last drive pulse, the trace drops quickly, and continues a further smooth decrease to almost zero until the next scan cycle begins , signifying a workable NFB system that has proven reliable and not needing further adjustment at this time. This pause circuit cannot be eliminated, as no useful candidate traces were observed with that turned off. The two NFB circuits have been re connected back to P4 and P5 and the extra output transistors removed, as they added no interesting traces, and the installation of an aluminum shield cover over the 7014 chip board has also helped overall stability. I found the while the newly reconnected NFB circuits allowed a trace that would occasionally show up that looked promising, the inherent noise in the scan mode now seemed to prevent that trace from becoming stable. I had left the two extra piezos in the stack unused, until I found that I could hook them up passively with various components and get significant reduction in scan noise. After much switching around on values, found that the trace stabilizes with only three components hooked up between the 2 absorber piezos, the 5 drive piezos, and ground. A 12k resistor, a 36 pf cap, and a 72pf cap. I believe these passive components cause a phase cancellation of scan noise and have allowed it to run a stable trace on the bench for hours. One of the useful things about the 7014 chip is that it's frequency output varies a few hertz upon raising and lowering the drive voltage to it. This has amounted to a vernier adjustment that has proved quite useful. One method of checking progress on this " drive noise phase cancellation" as I was subbing in dozens of parts, was to raise and lower the drive voltage, and seeing if the trace would fail and dissolve into chaos. After a few hours, a stable trace that varies in only trivial ways is observed as drive voltage is raised from 12v to 20v. Both of the asymmetric masses have been removed and no longer necessary. I will build another stack and try to use only one absorber piezo this time and use heavy aluminum foil as element contacts, as the phosphor bronze sheet metal has proven difficult to work with and the foil should conform better to element faces. I will also build a continuously variable power supply for the output transistors to raise the voltage slowly from the 300v I'm now using up to approx. 1kv. Some of the Woodward team have speculated that a potential thrust could increase at the square, or possibly the fourth power of the drive voltage increase.

Sorry about that last bit on the previous post, I thought I had deleted that. Today I mounted the sixth sensor piezo back into the stack, and as expected the #5 piezo helps the signal now, and the frequency of interest has moved up to just over 100kc. The reflection of the energy has always been the issue to be dealt with and that has me thinking that if there were several more "dummy load" piezos at the end of the stack, wouldn't that absorb the energy before it's reflected back towards the front of the stack? I had tried to scavenge energy off the reflected wave in the early mechanical tests, and actually got enough to light up an LED weakly. Being a passive load, it was a very inefficient transfer . If the neg feedback circuits were moved to the extra piezos, the electrostriction effect should remove the wave much more efficiently, so fewer elements needed, lowering complexity, weight and cost. The large steel mass would be replaced by the "absorber piezos", and the smaller front mass may no longer be needed. Another useful aspect is that the frequency of the drive stimulations may become more arbitrary as the feedback circuits will be on full time and not tied to the newly obsoleted pause circuity and therefore operate independently to eliminate whatever signals are presented to them. If any measurable thrust is developed, the stimulation frequency might act as thrust control. I would have to add separate output transistors for the absorber piezos. I don't think I would need all five channels, so will start by adding 3 more absorber piezos behind the 6th sensor piezo, for a total of 9 elements, and 3 attendant output transistors.

I have noticed that the damped wave trace at 71 khz is cleaner and has a higher output if the fifth piezo is turned off. This may be because the main shock wave travels through the first four piezos in one direction on the drive phase, but the 5th is now the turn around point as the wave reflects back towards the first piezo, quickly passing back through itself just as it's being stimulated, causing these instabilities and lowered output. I previously removed the 6th piezo from the stack thinking that would clean up the signals, and the opposite has happened, at least at this new 71 khz frequency. I will keep the side mounted sensor, but will install another piezo back into the stack as a sort of "dummy load" as well as a second sensor. From the beginning, I had been having issues with instabilities with the 7014 chip as the stack sometimes emits strong EMF hash that is picked up by the chip and confuses it's count process. The chip circuit board is now shielded in an aluminum box at the opposite end of the chassis and that has resolved the issue. for a total of 5 active elements, and 2 independent sensors. It may prove that the last piezo element needs to be electrically neutral, as the reflection point in this serially stimulated scenario.

Further refinements in the stack and mods on the NFB circuits have given a new maximum of measured output at 71 khz. Scope traces have stabilized on certain damped waves that look very interesting. Rates of damping shows an increase when NFB gain is increased. Also have installed a 4PDT switch to reverse the order of stimulation of the piezos. That will prove useful as I have placed asymmetrical masses at ends of stack, as the Woodward team has done. I will reverse the masses and repeat test of forward/ reverse differences.

re positioning of the 6th piezo has raised the frequency of interest to 1.8 mhz, much higher than I expected. Before the latest change, frequencies above 1 mhz were trivial scope fuzz. I am getting 6V p-p from this sensor arrangement. It seems productive to add more sensor piezos in this way, adding four more for complete coverage. Unless I had four more scopes, I would need to matrix the results. A decrease in the retrace delay was of course needed with this sensor change, but much less than expected.

It has seemed apparent since the beginning that the sixth piezo doing the monitoring of the waveform is a problem in it's placement. I have found that putting another piezo touching edge to edge of one in the stack offers a strong signal. The placement is like two car tires touching treads instead of sidewalls. To my surprise, the 5.5 mm thicknesses offer a good enough physical transfer of energy to give a strong signal output, observed from face contacts. My next alteration will be to remove the sixth piezo from the stack and place it outside the stack for monitoring from the edge of the center element of the stack, offering a more linear output of overall energy flows. This way, only active elements are in the loop, and the monitor element will become a negligible factor in stack behavior. This is one more reason not to clamp the assembly too tightly, and to use slippery poly washers between each element, allowing lateral physical movements. I have also changed the .002 cap in the enable circuit to .0039 to center up the sweet spot on the 10k delay control. Another planned change is to raise the output transistor voltage supply from +150V up to approx +250V.

Using the 7014 chip with a +10V supply, am using odd numbered outputs, 1,3,5,7,9 to drive the stack as this allows an equal time gap between pulses. The neg. feedback ckt. needs to be activated in an equal time to the total forward scan, so I have output 10 hooked to the enable pin with a .002 capacitor in series with a control set approx. at 2.7k ohms. This gives a controllable pause till you want the pulse order to begin again. I find it convenient to have all outputs hooked to LEDs, as with a fast scan one can easily tell pulse duration of each output by relative brightness. Individual switches to each output transistor allow base drive to go to the transistor, or to be shunted to ground through a 1.8k ohm resistor. I have found that through adding and subtracting piezos, that a clear overlap of pulses occur at a drive frequency of 340 khz. The stack is one and a half inch, center to center, including 4 poly washers approx 2 mm thick and 10 thin electrode attachments of stainless steel. There is a sixth piezo at the end only used to scope the waveforms, and so not included in the length measurement but is the same 5.5 mm element. Although the sixth piezo is passive, it does absorb and reflect the pulse, so does contribute to overall pulse speed calculations. As the neg/ feedback circuit is switched off, then back on, a clear display of removal of most harmonics is observed. The neg. feedback circuitry is normally on only between scans. The next step is to build a non-inverting op amp twin tee circuit to insert into the signal path, which will be active during both the scan and retrace modes, with a 340 khz notch. This hopefully will remove harmonics as they are being produced, without overly attenuating the 340 khz. This might make the overall trace more clear and perhaps add to pulse amplitudes by the additional removal of "noise" in the system. A possibly unavoidable source of noise is that the drive is square wave and the Woodward team says piezos like sinewaves better, but it may not make much difference at a drive frequency so much higher than the 25khz resonance.

I ordered ten 7014 ICs from Newark Electronics (formerly MCM) and all were defective. Under close examination the logo is blurry and indistinct. I have ordered most of the parts for this project from them with no other problems. Last week I re-ordered ten more 4017s online from Amazon, got them today with a Texas Instrument logo that is clear, and the first three I have tried work correctly both in the solderless breadboard and the prototype board.

how would neutrinos interact with an encounter with a black hole? Are they capable of a closer orbit to the event horizon without falling in due to the negligible mass, or would that matter? thanks

well, there is no reverse scan in the present scheme...should have said " thrust in the direction opposite of forward scan".

early mechanical experiments indicated the possibility of scavenging the return energy by dumping the reverse shock wave into a dummy load resistor. I did get some interesting waveforms across this load that were trapezoidal (sloping square wave) and very regular and that didn't change waveform when slowing down the stimulation. By adjusting tensioner nut on the center pin thus adjusting mechanical pressure on each element, a sweet spot was found indicated by a moderate compression that produced maximum voltage output on the scavenged signal. (The woodward crowd glues and clamps each element very solidly and I think that is a problem. The elements must be allowed to move, or the shock wave is largely converted into useless harmonics). But this dummy load was only a passive load to the unwanted shock wave, so I have the active neg feedback system which should be more effective in nulling the retrace wave. A possible way of upping the efficiency might be to try to hit each piezo, then hold the volatage on each one to the end of forward scan, then drop the voltage serially, as the shock wave travels back, thus absorbing it as much as possible within each piezo, instead of neutralizing it with the neg feedback electostriction. As the reverse wave hits each piezo, it's loss of voltage will not only shrink in the needed direction, but the wave may compress the element slightly as it passes, thus generating a voltage that could be recycled into the next forward scan sequence. This form of retrace period might require a higher scan rate, as the piezos will collapse even if the voltage is held steady and physically self-compress at the 25khz time constant (resonance) and so require a doubly accurate pulse timing management. The first electronic experiments will drive the stack until the temperature stabilizes, then turning on the neg feedback system. At that point an increase in temp would seem to indicate that the return wave is being converted to heat through electrostriction...thus the possibility of thrust in the direction of reverse scan. Still waiting for the 4017 parts, hope the corona thing doesn't significantly delay delivery.

Actually the pan balance test isn't quite so simple. A laser pointer is aimed at a mirror placed on the scale with an acute angle, and the beam is reflected onto a distant surface to display amplified small movements.